Metal Roof Repair in Los Angeles
Metal roof repair in Los Angeles fixes leaks and wear on standing seam and corrugated metal roofs: backed-out or worn fasteners, open seams, failed sealant at laps, rust, and flashing at walls and penetrations. These roofs are found on modern homes, hillside houses, garages and commercial buildings. Emergency Roof Repair LA connects you with a local provider.

Where are metal roofs found around Los Angeles?
Metal roofing has become popular on modern and contemporary homes, on hillside rebuilds where a light, fire-resistant roof is attractive, on ADUs and studios, and for decades on garages, workshops, barns in the canyons and light industrial buildings.
Standing seam panels with hidden fasteners and exposed-fastener corrugated or ribbed panels behave quite differently when they leak.
Common metal roof problems
- Exposed-fastener roofs. Rubber washers on screws dry out in the sun. Screws back out as panels expand and contract between hot days and cool nights, and leaks start at each fastener.
- Open laps. Panel side-laps and end-laps where sealant has failed.
- Standing seam flashing. Leaks at ridge caps, walls, skylights and pipe penetrations, rather than through the panels.
- Corrosion. Rust at cut edges, scratches, and where dissimilar metals touch, such as copper pipes against galvanised steel.
- Wind. Lifted panel edges or trim after strong wind.
- Foot traffic. Dents and oil-canning from people walking on the roof, which can open seams.
How is a metal roof repaired?
Fasteners. On exposed-fastener roofs, worn screws are replaced with new screws and washers, sometimes one size up where the hole has widened. Laps are cleaned and resealed with a sealant compatible with the panel coating.
Standing seam. Repairs focus on trims and flashings. Damaged panels may be replaced individually, depending on the profile.
Rust. Rust is cleaned back, treated and coated. Heavily corroded panels are replaced.
Penetrations. Pipe penetrations get new boots made for metal roofs, sealed to the panel profile.
Coating. For an ageing but sound roof, a full restoration coating with seam reinforcement can extend its life.
Safety. Metal roofs can be slick, especially with morning dew, so experienced crews use proper fall protection and soft-soled footwear.
What affects the cost and time?
- Panel type: exposed-fastener or standing seam.
- Roof size and pitch.
- Number of penetrations.
- Extent of rust.
- Availability of matching panels and trims.
- Whether the work is a targeted repair or a full fastener replacement and recoat.
Exposed-fastener versus standing seam
| Exposed-fastener | Standing seam | |
|---|---|---|
| Common on | Garages, sheds, barns, industrial units | Modern homes, ADUs, hillside rebuilds |
| Usual leak points | Screw washers, laps | Trims, flashings, penetrations |
| Maintenance | Periodic fastener checks | Low, but check flashings after wind |
Metal roofs and fire zones
Metal roofing can form part of a Class A fire-rated assembly, which is why it is often chosen in hillside and canyon areas. When repairing or adding to a metal roof in a high fire hazard zone, keep the whole assembly's rating in mind, including the underlayment, and seal gaps at ridges and eaves where embers could enter.
Before the roofer arrives
Note where the water shows up and whether it follows wind from one direction. Look from the ground for lifted trim, missing screws or rust streaks. If a panel is flapping in the wind, keep people and cars clear of that side of the building until it is secured.
Frequently asked questions
Why does my metal roof leak around the screws?
The rubber washers under exposed screws dry out in the sun, and screws loosen as the panels expand and contract each day. Replacing worn fasteners with new screws and washers usually stops these leaks.
Can rust on a metal roof be repaired?
Surface rust can be cleaned, treated and coated. Panels rusted through, or badly corroded at laps and edges, are usually replaced.
Is it safe to walk on a metal roof?
Walking on metal can dent panels and is slippery, especially with dew. Leave it to roofers with proper fall protection and footwear.
Can a metal roof be coated?
Yes. Sound metal roofs are good candidates for restoration coatings, applied after fasteners, laps and rust spots are repaired.
Are metal roofs good for fire areas?
Metal roofing can be part of a Class A fire-rated roof assembly, which is valued in Very High Fire Hazard Severity Zones. The rating depends on the full assembly, not just the panels.
Related services
Areas we cover
Need metal roof repair in Los Angeles?
Call Emergency Roof Repair LA any hour. Your call is answered by a participating independent roofing provider in your area.