Emergency Roof Repair LA (000) 000-0000

Roof Flashing, Chimney and Vent Repair in Los Angeles

Roof flashing repair in Los Angeles replaces the metal and boots that seal the joints of a roof: where it meets walls and chimneys, around plumbing vents and skylights, and in valleys. These joints cause most leaks on otherwise sound roofs. Emergency Roof Repair LA connects you by phone with a local provider, 24/7.

Call (000) 000-0000

Free call. Lines open 24 hours a day, 7 days a week. Calls are answered by a participating local provider.

Illustration of Los Angeles homes with a mix of tile, shingle and flat roofs beneath the hills, for flashing, chimney & vent repair in Los Angeles

What is roof flashing and why does it fail?

Flashing is the sheet metal, and sometimes rubber or lead, that bridges the gap wherever the roof covering stops. That includes:

  • along a wall;
  • around a chimney;
  • at a skylight curb;
  • around a vent pipe;
  • down a valley where two slopes meet.

The roof covering itself often lasts longer than these joints.

In Los Angeles, flashing tends to fail for a few reasons:

  • Rubber pipe boots crack in the sun.
  • Sealant that was used instead of proper lapped metal dries out.
  • Chimney counter-flashing loosens as mortar ages.
  • Stucco walls crack and let water behind the flashing.
  • Older masonry chimneys may have been damaged in past earthquakes. That shows up as gaps at the roofline, and it can need a mason as well as a roofer.

Where do flashing leaks usually show up?

  • Stains on the ceiling or wall right next to a fireplace chimney.
  • Water around bathroom or kitchen exhaust fans and plumbing walls.
  • Drips at the top of an inside wall where a lower roof meets a two-storey wall.
  • Leaks under valleys, especially after leaves have built up.
  • Water around attic furnace flues and B-vents.

How is flashing repaired properly?

Step flashing. On shingle roofs, step flashing along a wall is a series of L-shaped pieces woven into each course. A proper repair removes the shingles along the wall and installs new pieces, with counter-flashing or a stucco stop covering the top edge. Running a bead of caulk along the joint is not a substitute.

Chimneys. Chimneys get base flashing, step flashing up the sides, a cricket (a small saddle) on the uphill side of wider chimneys to divert water, and counter-flashing set into the mortar joints. On tile roofs, the tiles around a chimney or wall also need lead or formed flashing dressed over their profile.

Pipe boots and vents. These are replaced with new boots. Many providers prefer metal or silicone boots that resist sun damage better than basic rubber.

Valleys. Valleys may be re-lined with new metal and kept open so leaves wash through.

What affects the cost and time?

  • How much roofing must be lifted to reach the flashing.
  • Tile roofs take longer than shingle.
  • Chimney size and condition.
  • Whether stucco needs cutting and patching.
  • Whether a mason is needed for the chimney itself.

Most single flashing repairs are completed in one visit.

Caulk patch or proper flashing?

Sealant patches compared with replacing flashing
Sealant patchFlashing replacement
TimeMinutesHours
How it sheds waterRelies on the bead staying bondedOverlapping metal sheds water by gravity
In LA sunDries and cracksLong-lived when installed correctly
Good forTemporary stopgapPermanent repair

Frequently asked questions

Why does my chimney leak only in heavy rain?

Wind-driven rain gets behind loose counter-flashing or into cracked mortar and brick. Wider chimneys without a cricket on the uphill side can also hold water against their base.

Can I just caulk the flashing myself?

Caulk can slow a leak briefly, but it cracks in the sun and can trap water. Lasting repairs replace or properly re-set the flashing so it sheds water by overlap.

How do I know if a vent pipe boot is leaking?

Look for stains on the ceiling near bathrooms, kitchens or laundry areas, and check the attic around the pipe for damp wood. From the ground with binoculars, a cracked or split boot is often visible.

Do chimney leaks need a mason or a roofer?

Flashing is roofing work. Cracked crowns, loose bricks or failed mortar are masonry work. Some leaks need both, and a roofer will tell you if a mason is required.

What is a chimney cricket?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney so water flows around it instead of pooling against the brick. Wider chimneys usually need one.

Need flashing, chimney & vent repair in Los Angeles?

Call Emergency Roof Repair LA any hour. Your call is answered by a participating independent roofing provider in your area.

Call (000) 000-0000

Call now: (000) 000-0000